SONEL POLAND

Wire and Pipe Locator
Characteristic features:

• backlit LCD with contrast (auto on-off),
• automatic adjustment of detection sensitivity,
• 5 operating modes,
• warning about shallowly located cables,
• measuring cable locations up to 3 m deep,
• determining the direction of a cable,
• sound signals to facilitate locating or tracing,
• adjustment of power and selection of frequencies for the transmitter,
• passive or active modes of tracing.
• detection of underground live wires.
• detection of underground wires with no voltage (radio mode)
• detection of underground wires with no voltage using a transmitter (galvanised, inductive or clamp-based connection).
• tracing metallic or non-conductive pipes using an additional probe. tracing non-conductive pipelines using a “floating” probe.
• tracing a determined cable.
• determining the depth of a cable.
• Operating modes: passive, with 50 Hz or 60 Hz – enables to locate live wires and cables (POWER):

Earth Resistance Meters:
MRU-200 is the unique meter in the market which uses all measurement methods.

• earth resistance measurement with 2-pole,3 -pole,4-pole method
• selective earth resistance measurement with clamp (no influence from parallel earths; no opening of rusty junctions is needed),
• Impulse earth resistance measurement, three kind of measuring impulse 4/10µs, 8/20 µs, 10/350 µs
• Two clamps earth resistance measurement without auxiliary test probs
• Earth resistivity measurement
• Leakage current measurement
• Selection of maximum measuring voltage (25V and 50V).
• Memory of 990 measurements
• Data transmission to the computer (USB).
• Real time clock (RTC)
• Measurement of interference voltage and frequency.
• Indication of battery state

Insulation resistance Meter:

• Insulation Measurement upto 40TΩ
• Insulation testers are available from 1kv to 10KV.
• measurement voltage any in the range of: • 50...5000 V for MIC-5050 (50...1000 V at 10 V and 1...5 kV at 25 V),
• 5010000 V for MIC-10k1 (50...1000 V at 10 V and 1...10 kV at 25 V),
• Measurements of Insulation resistance, leakage current, polarization index, absorption coefficients, dielectric absorption ratio, actual test voltage during measurement.
• Bluetooth and wireless communications
• The device meets the requirements of EN and IEC standards
Low resistance Measurements:

• MMR-620, MMR-630.
• Measurements of Inductive object type (Measurements of windings of motors, transformers, low resistance coil).
• Measurements of resistive object type. (welded and soldered connections, equipotential bonding, earth wire,terminals and connectors, rail welded joints, cables and wires,measurement 4-pole method.)
• Measurement in normal, automatic and continous mode.
• Capability of performing measurements with interferences of values even 5 times higher than the measured values.
Thermal Imagers/Pyrometers:

• Infra fusion technology
• KT-130,140,150,160,160A,384,640.
• Temperature range -20 to 800 °C
• File format JPEG (an invidual file consists of infrared image, visual image, voice annotation / AVI video)
• Image refreshing rate 50/60 times per second.
• 8 colour palettes available.
• Three hours continous operations with rechargeable batteries.
Power Quality Analyzers:

• PQM-701,701Z,701Zr
• Power Quality system works for single phase, double phase with N wire, three phase wye type, with and without N wire, 3 phase delta type, with constant voltage.
• Active, reactive, distortion, apparent power, including the type of reactive power (capacitive, inductive).
• Power recording: Budeanu method IEEE 1459
• Current and voltage waveforms recording after each averaging period.
• Designed for nominal frequency 50/60Hz and nominal voltage 690V.
• Measured Total Harmonic Distortion (THD) for voltage and current,
• Confirming to EN & IEC standards.
Cable Fault Locator: Cable fault location – TDR 410

• Location damaged power cables.
• Fault location copper telecom cables.
• Coaxial cable fault location.
• Fault location wiring infrastructure.
• Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.
• Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.

PAT – Portable appliance Tester: portable appliance tester.
• Checkup of safety of information technology equipment ( IT Equipment).
• Measurement of parameterss of arc welding machines (EN 60974-4).
• Measurements od all industrial Appliances.
• Household and similar electrical appliances – safety.
• Safety of transportable motor-operated electric tools.


Laboratory Equipments: SRP-50-K0-5TO, SRP-50K0-10G0, SRP-50K0-100G0

• Remote control of the calibrator, creating & saving automatic programs for checking tested devices.
• Changing display brightness & keyboard pressing sound
• Selection of software interface language
• Updating of the software from USB interface
• Auto optical inspection, ion cleanlines testing, functional tests & electrical test PCB.